This Article Applies to:
HS103P3 , HS103P4 , HS100P3 , HS103P2 , EP40 , EP40A , HS107 , HS200P3 , EP10P2 , EP10P3 , EP10P4 , KP105P2 , HS105 KIT , HS103 , KP105P3 , HS300 , KP115 , HS105 , HS200-BL , HS110 KIT , HS220 , HS200 , KP100 KIT , HS100 , HS220-LA , HS110P3 , KP100 , KP400 , EP10 , KP125 , KP200 , HS100 KIT , KP405 , KP105 , HS210 KIT , KP401 , KP303 , EP40M , HS110 , HS210 , KP400P2 , HS200-LA
Recent updates may have expanded access to feature(s) discussed in this FAQ. Visit your product's support page, select the correct hardware version for your device and check either the Datasheet or the firmware section for the latest improvements added to your product.
Just like any other electrical appliance, the smart plug radiates heat during operation. It would feel warm or maybe a little hot after working for a while depending on the environment. The cool and well-ventilated environment is ideal for the plug, and please try the following suggestions if it feels warm:
1. Put your smart plug in the open area, not cover it with any objects, and avoid placing it in a closed space, not let it suffocate;
2. Keep your smart plug away from direct heat or excessive sunlight;
3. It is not allowed to plug any electrical appliance whose power exceeds the Kasa plug's maximum load and power, otherwise it would cause some safety issue or even a conflagration. Please also note some devices have very high peak current when it powers on and that high peak current would also damage the smart plug;
4. If the Kasa plug is too hot to touch or smells burnt, please stop using it immediately, and please contact our support team to collect the following information for further assistance. Thanks in advance for your cooperation.
a. What’s the model name and version number of your smart plug?
b. What’s the type of outlet the device was used in? Was it a GFIC, AFIC, or Standard? Was this outlet grounded?
c. What was the product or device used with this smart plug? What’s model of that device?
d. What’s the Location the product was used in? Bedroom, Living room, Kitchen, etc.
e. How long did it work before this incident?
f. Was there any unusual behavior with the device before this incident?
g. Please if possible provide pictures of the outlet, the TP-Link device, and the device that was connected to it.
Is this faq useful?
Your feedback helps improve this site.
What’s your concern with this article?
- Dissatisfied with product
- Too Complicated
- Confusing Title
- Does not apply to me
- Too Vague
- Other
We'd love to get your feedback, please let us know how we can improve this content.
Thank you
We appreciate your feedback.
Click here to contact TP-Link technical support.
FAQs
A plug that becomes hot to the touch may be shedding "waste heat." This is energy that the plug cannot pass through to the appliance, so the plug itself begins to heat up. A warm plug is not overly concerning, but a HOT plug should be unplugged and investigated.
Is it normal for a plug to feel warm? ›
A plug that becomes hot to the touch may be shedding "waste heat." This is energy that the plug cannot pass through to the appliance, so the plug itself begins to heat up. A warm plug is not overly concerning, but a HOT plug should be unplugged and investigated.
Why does my outlet feel hot? ›
Outlet Is Overloaded
As more electricity runs to the outlet, you'll notice that you have a hot outlet because of increased power. This issue can typically be solved by unplugging items from the outlet. Then, give the outlet a few hours to cool. If the outlet is still warm, stop using it and call your electrician.
How do I fix my smart plug not responding? ›
For smart plug:
Try to plug a different device into the plug, like a lamp or a light. Unplug the smart plug from the power outlet, then try gently tapping the side of the plug: pick it up and gently tap its side to a level surface. Check the link below to reset the smart home devices, then configure it again.
Which is the hot on a plug? ›
A receptacle's top two slots, or “eyes,” are meant for the vertically aligned plug prongs, while the rounded bottom slot is intended for the ground prong. At a casual glance, these two slots look the same but look closer, and you'll quickly see one slot is smaller than the other. This is the hot side.
What causes a plug to melt? ›
Overloaded circuits and defective wires may cause sparks and overheating which causes outlets to melt, but it can also damage the surrounding area and other property. This is how electrical fires can start which can have a potentially devastating impact on one's home and life.
Why is my plug hot and smells? ›
Electrical outlet smells can be an indication of dangerous overheating, especially when they are accompanied by black marks, buzzing or crackling sounds. A burning outlet smell should not be taken lightly and it's best to proactively take steps for safety.
How do you cool down a hot outlet? ›
If your electrical outlet is hot, try the following fixes to address the problem:
- Turn off the circuit breaker that powers the hot outlet. ...
- Unplug everything connected to the hot outlet. ...
- Unplug any devices with a transformer. ...
- If you have multiple devices plugged into one outlet, spread them out.
If your Amazon Smart Plug stopped working, restart your device. Unplug your Amazon Smart Plug from the outlet, and then plug it back in. Reset your Amazon Smart Plug: press and hold the button on the side of the device for 12 seconds.
How do you reboot a smart plug? ›
To restart, unplug the device from the outlet and plug it back in. If you have restarted your device and it still isn't working, reset your Amazon Smart Plug: Press and hold the button on the device for 12 seconds. Release the button once you see the red LED light.
A hot plug indicates that the connection between the plug and socket is not perfect (i.e., not zero resistance). But a perfect connection is impossible, so some heating is normal. Too hot to touch is dangerous. Warm-to-hot, especially in a high current appliance like a coffee maker, is normal.
Why does my 3 pin plug get hot? ›
The pin that gets hot is the live terminal. The reason is it might be loose or it is drawing more current than it should be hence it heats up. If you have appliances that draw high currents and you fit in the wrong plug, that plug will heat up.
Why is my electrical outlet hot? ›
Essentially, it's more electricity than it can handle. When excessive demand is placed on a singular electrical circuit breaker, outlets become hot to the touch and may trip the circuit breaker inside your electrical panel. That's a sign you may need to replace your electrical panel.
Should charger plugs get warm? ›
Key Takeaways. Phone chargers convert alternating current (AC) to direct current (DC) to charge your phone, which generates heat. It is normal for a phone charger to get warm while in use, but it should never be hot enough that it becomes uncomfortable to hold or touch, or that it begins to melt or become discolored.
Is it normal for electrical wires to get warm? ›
Electric cables often feel warm in normal use, this is to be expected. Copper and aluminium conductors, like all metals, have an inherent electrical resistance, so they cannot be perfect electrical conductors. A cable with a current passing through its wires encounters electrical resistance and will produce heat.
How do you tell if you have a bad outlet? ›
5 Signs of a Bad Electrical Outlet
- Burned Outlets or Smell of Burning Wiring. One of the most apparent signs of a bad electrical outlet is a burn mark on its surface or the wall around it. ...
- Loose Outlets. A loose outlet is an indication of age or damage. ...
- Overheating Outlets. ...
- Flickering Lights. ...
- Tripping Circuit Breakers.
